捷科10支装镜抛双梅呆扳手套装 Jieke 10 Pack Mirror Double Plum wrench set OFSF-S10

$25.89

捷科10支装镜抛双梅呆扳手套装OFSF-S10/1套
镜抛扳手采用碳钢锻造,采用薄型设计,适合在狭小空间使用表面经过多道抛光和研磨程序
Jieke 10 Pack Mirror Double Plum wrench set OFSF-S10/1
The mirror throwing wrench is forged from carbon steel and has a thin design. It is suitable for use in a small space with multiple polishing and grinding procedures.

明细
6-78-1011-1312-1414-1717-19,21-2322-2424-2730-32

Detail
6-78-1011-1312-1414-1717-19, 21-2322-2424-2730-32

120 in stock

Compare

Description

捷科10支装镜抛双梅呆扳手套装OFSF-S10
梅花扳手两端呈花环状,其内孔是由2个正六边形相互同心错开30°而成。很多梅花扳手都有弯头,常见的弯头角度在10°~45°之间,从侧面看旋转螺栓部分和手柄部分是错开的。这种结构方便于拆卸装配在凹陷空间的螺栓、螺母,并可以为手指提供操作间隙,以防止擦伤。用在补充拧紧和类似操作中,可以使用梅花扳手对螺栓或螺母施加大扭矩。梅花扳手有各种大小,使用时要选择与螺栓或螺母大小对应的扳手。因为扳手钳口是双六角形的,可以容易地装配螺栓/螺母。这可以在一个有限空间内重新安装。
在使用梅花扳手时,左手推住梅花扳手与螺栓连接处,保持梅花扳手与螺栓完全配合,防止滑脱,右手握住梅花扳手另一端并加力。梅花扳手可将螺栓、螺母的头部全部围住,因此不会损坏螺栓角,可以施加大力矩。
扳转时,严禁将加长的管子套在扳手上以延伸扳手的长度增加力矩,严禁捶击扳手以增加力矩,否则会造成工具的损坏。
严禁使用带有裂纹和内孔已严重磨损的梅花扳手。

Jieke 10 Pack Mirror Double Plum wrench set OFSF-S10
The end of the plum blossom wrench has a flower ring shape, and the inner hole is formed by two regular hexagons staggered by 30°. Many plum wrenches have elbows. The common elbow angle is between 10° and 45°. The rotating bolt part and the handle part are staggered from the side. This structure is convenient for disassembling bolts and nuts assembled in the recessed space, and can provide an operating gap for the fingers to prevent scratches. For use in supplemental tightening and similar operations, a wrench can be used to apply high torque to the bolt or nut. The wrenches are available in various sizes and should be selected with a wrench that corresponds to the size of the bolt or nut. Because the wrench jaws are double hexagonal, bolts/nuts can be easily assembled. This can be reinstalled in a limited space.
When using the wrench, push the plum wrench and bolt connection with your left hand to keep the wrench and bolt fully fit to prevent slipping. Hold the other end of the wrench in your right hand and apply force. The wrench can completely enclose the head of the bolt and the nut, so the bolt angle is not damaged and a large moment can be applied.
When turning, it is forbidden to put the lengthened pipe on the wrench to extend the length of the wrench to increase the torque. It is strictly forbidden to slam the wrench to increase the torque, otherwise the tool will be damaged.
It is strictly forbidden to use a wrench with cracks and severe wear on the bore.

 

Leave a Reply

Your email address will not be published. Required fields are marked *

X